How To Fix 0x0000000A Error
“Stop 0x0000000A” error in Windows XP is very annoying and disappointing, to prevent your computer from being able to run easily or reliably, as you wish, luckily, there is a solution to fix this blue screen error, which You can read below:
What Is The Stop Error code 0x0000000A ?
Stop 0x0000000A Error is usually when a driver on your operating system tries to reddish a memory address that is not present or corrupted. This causes your system to become extremely unreliable because it prevents it from using any specific hardware that has a faulty driver.
This error can also be seen if you have messed up the system files or the damaged hardware, it is basically XP’s “ejector seat” if it reaches any critical problems that fail to deal with your system service could. Fortunately, it’s actually really easy to fix this.
How to Fix the Stop 0x0000000A Error
Method 1 – Reinstall XP & Specify the Correct “HAL”
This is for advanced users who know how to install Windows XP. You will need an installation disc to install it so that you can restore XP to your system. Here’s what to do:
- Restore XP Installation Disc and Boot With It or try using device driver.
- During the installation startup, “Set up is monitoring your computer’s hardware configuration” message is displayed, press F5.
- When you are prompted, make sure you specify the correct computer type and Hardware Abstraction Layer (HAL). For example, if you have a processor, specify “standard PC” HAL.
- Try restoring Windows XP
- If this correction fixes the error message and you successfully install Windows XP, you are finished.
- If this stop does not resolve the error message, go to Method 2
Method 2 – Turn Off Features in BIOS
This is for advanced users who are aware of your PC’s “BIOS”. You should proceed with caution since this point of time, changing the wrong BIOS setting can seriously compromise your system:
- Restart your PC and load up the BIOS
- Turn off all the following features in the CMOS settings of your computer. For instructions, see the hardware documentation or contact the manufacturer:
- All caching, including L2, BIOS, internal/external, and write back caching on disk controllers
- All shadowing
- Plug and Play
- Any BIOS-based virus protection feature
- Try to reinstall Windows XP.
- If this resolves the Stop error message, go to step 3.
- If this stop does not resolve the error message, go to method 3.
- Try to isolate which feature is causing the error. To do this, re-enable each of these features one at a time, and then restart your computer after you re-enable each feature.
- If you identify the issue problem, disable or remove it and contact the manufacturer to resolve the problem. If it does not separate the problem with the CMOS setting, but it fixes the stop error message and you can normally start your computer, it may be that a setting is stopping the installation. This is the case, then after you install Windows XP, turn on the set, you are finished.
Method 3 – Remove Any Hardware and Adapters
- Remove all adapters and disconnect all hardware or software devices that are not required to start the computer or to install Windows. This includes the following adapters and devices:
- SCSI devices
- IDE devices
- Network adapter
- Internal Modem
- Soundcard
- Extra hard disks (you have to have at least one to complete the installation)
- CD drive or DVD drive (if you are installing from the local hard disk)
- Try to reinstall Windows XP.
- If this resolves the Stop error message, continue to step c.
- If this does not resolve the Stop error message, go to method 5.
- Try to generate different adapters or hardware devices due to errors after reinstalling or recovery options of Windows XP, reconnect each adapter or hardware device at a time. Restart your computer after adding each one again and then updates drivers ad access a memory using command prompt.
- If it separates a problem with the hardware, disconnect the adapter or device and contact the seller to resolve the problem. It does not separate the problem with the hardware, but it fixes the stop error message and you can start your computer normally, it may be that some hardware was blocking the installation. If this is the case, then reconnect the hardware after you install Windows XP, and then you will finish.
Method 4 – Clean the Registry
The registry is a large database that is dependent on running Windows. It stores information from your latest email, desktop wallpapers, and even your hardware settings. A registry is an important part of XP, but there is also a big reason for the 0x0000000A error in the registry.
There are lots of hardware references in the registry, which require XP to run. This is often the case that many of these references become damaged or corrupted, which will make them unable to read XP. This can happen because the Stop 0x0000000A error as XP will be unable to read your system’s hardware references.
Cleaning the registry with a registry cleaner can be one of the most effective ways to boost the reliability of your XP machine
.