Site icon Techies Post



Fix: Windows Cannot Install Required Files Error 0x80070570

Error 0x80070570 occurs usually when you are installing Windows 7.  There are numerous suggestions all over the internet for resolving this issue, some are quite time-consuming, such as running memtest which takes a couple of hours – Don’t worry, if you don’t know what memtest is, we’ll come to it. In this guide, I’ll start with the easiest methods; you start from method 1 and stop at the one that worked for you.

Way 1: Re-try Install (0x80070570) in your system

After that install is in progress, and go to this error “0x80070570” than press OK and go back to the previous screen, after that the installation process again and re-do the installation process without restarting. Try this like 3-4 times as I know it worked for some.

If the error doesn’t pops-up again, then you can stop at this method.

Way 2: Pull Your RAM in your computer 0X80070570

If you have only one memory stick slot, then proceed to

Way 3 – but if you have more then one, then try pulling one of it one by one.

Note: If you have 4 DDR2 STICKS, after that then pull the other one and test, then pull the other one and test until it  works, if none of it works, put all back and proceed to

Way 3.1 – If it works, then the one without which it worked is faulty. However, you must have a 2GB in all the time. If you have 1GB RAM Stick, then test with 2 in – the aim here, is to find the faulty ram if there is any.

Way 3.2: MEM TEST to fix 0X80070570

Now run – From the there site, you can find bootable precompiled ISO. You can simply download and boot from it by writing it to a USB Drive or A CD Drive. You will need to change your boot order.

When you run mem test, here’s what the screen will show if the test fails you will be shown a message on the screen.

If it shows reports a fault with the memory, then the one stick you’ve been using is faulty and needs to be replaced. If it doesn’t, then proceed to way #4

Way 4: (Re-write ISO Files)

Download the Windows 7 ISO File on a different computer and write it to a USB Drive. I have an article written on this on how to do it – Create Bootable Windows 7 USB Once this is done, you can boot from the USB and try to install it.

PRO TIP: If the issue is with your computer or a laptop/notebook you should try using the Reimage Plus Software which can scan the repositories and replace corrupt and missing files. This type works in most cases, where the issue originated due to a system corruption. You can download Reimage Plus by Clicking Here

Way 5: Account Creation via Command Prompt

When you prompted by the error, perform the steps given below.

  1. Hold SHIFT and press F10 (SHIFT + F10) to open the Command Prompt.
  2. Type CD C:windowssystem32oobe and press Enter (If you are already in C:windowssystem32 or if there is an error then type CD oobe only)
  3. After that type msoobe and press Enter Now windows account creation wizard should be open in front of you. Follow the on-screen instructions to create a generic user account and then reboot the system. This should solve the error.

Way 6: Using MMC

  1. Hold SHIFT and press F10 (SHIFT + F10) to open the Command Prompt.
  2. Type MMC
  3. Click File then select Add/Remove Snap-in…
  4. Click Computer Management
  5. Press Add
  6. Click Local Computer
  7. Click Finish then press Ok
  8. Select Computer Management
  9. Select System Tools
  10. Choose Local Users and Groups
  11. Select Users
  12. Double-click Administrator
  13. Uncheck Account disabled and select Ok
  14. Right-click Administrator and select Set Password…
  15. Pick a password that you want to show it

Now restart your computer and it should solve the problem.

Way 7: Using Up and Down keys

A quick solution for this is to use up and down keys. When you see the first black screen on your computer after that restarting your computer then start pressing up and down arrow keys on your keyboard.

This doesn’t always work but is known to solve the issue for a considerable number of users so it’s worth a try.

Way 8: After that Activating Default Administrator Account on computer screen

If did not solve your computer problem and if you can not see the “Local Users and Groups” show your screen option in way 2 then this should solve the problem.  After that, the “Local Users and Groups” option isn’t available on some version of Windows especially the Windows 7 Home version.

So the steps given below are an alternative way to activate the default administrator account

  1. After that, hold SHIFT and press F10 (SHIFT + F10) to open the Command Prompt.
  2. After that, type net user administrator /active:yes and press Enter
  3. Then, type net user administrator password /active:yes and press Enter

(Note: replace your “password” with the actual password that you want to set for the default Administrator account) (NOT SURE ABOUT THIS STEP CHECK BEFORE POSTING)

  1. Now restart your computer

After that maybe the error 0X80070570 problem will be resolved in your Windows 10, but if you continuously facing this error issue. Then you have to get in touch with the technical experts.

If you need technical Support then call to Online technical support number. Here you get the best technical help on the related issues.

Exit mobile version